Nextera vs Nextera XT: what´s the difference?

[Simone78]

Hi all,
I tried to figure out the difference between Nextera and Nextera XT kit (for low input). With the Nextera kit I was never able to get good libraries when starting from <1 ng input DNA, while with the Nextera XT kit I got great results from <100 pg DNA.
I believe the enzyme is the same (I don´t think Illumina took the effort to engineer the transposase twice when they bought Epicentre Technologies...), so the difference must lie in the buffer.
I am quite sure that the Nextera kit uses a regular Tris+MgCl2 buffer, but what about the XT kit?
Any help is greatly appreciated!

[luc]

I would guess they reduced the enzyme concentration and added polyethyleneglycol (PEG) to the buffer to reduce the available volume (similar to the rapid ligation protocols).

[Simone78]

thanks! actually I just got some decent results today, just increasing the ionic strength of the final solution (adding potassium acetate). lower yield but similar profile at the Bioanalyzer

[slees]

I am also curious about this.
Also, why does Illumina suggest to use Nextera XT to make libraries only for small genomes? Can we directly use Nextera XT to make libraries for small amount (<1ng) of mouse/human genomic DNA instead of optimizing the buffer in Nextera kit?

[kcchan]

A diploid copy of the human genome is about 7pg. A 1ng sample would only have a bit over 100 copies of the genome, which is probably too little to generate a good library from.

[slees]

Good point. Thanks kccchan!

[Simone78]

for the genomic DNA 1 ng could be too little. I am doing single-cell RNA-seq and when starting from 1 ng or less (after RT & pre-amplification, of course) we get very high-quality data.

[slees]

Thanks Simone78. It will be great if you could also tell us something you have found about how the ionic strength of the final solution affects the reaction.

[Simone78]

Thanks Simone78. It will be great if you could also tell us something you have found about how the ionic strength of the final solution affects the reaction.

sorry, but that it´s going in a paper that we are going to publish (relatively) soon. Almost ready for submission, it´ll still take a few months, I am afraid

[slees]

Thanks Simone78. Good luck with your paper! And would you please let me know when it is published?

[slees]

how to make good libraries from &lt;1ng DNA using the Nextera kit

Hi Simone78, I was wondering if your paper has been published? I'm still interested in how to make good libraries from <1ng DNA using the Nextera kit. Thanks!

sorry, but that it´s going in a paper that we are going to publish (relatively) soon. Almost ready for submission, it´ll still take a few months, I am afraid

[Simone78]

Hi Simone78, I was wondering if your paper has been published? I'm still interested in how to make good libraries from <1ng DNA using the Nextera kit. Thanks!

yes, we published it in Genome Research last July. Here´s the PMID: 25079858.
Best,
Simone

[kobeho24]

yes, we published it in Genome Research last July. Here´s the PMID: 25079858.
Best,
Simone

Hi Simone,
Recently I've got the plasmid from you guys as a generous gift, and gave a try to purify the Tn5 Tnp. After following every single step of the protocol (except for the competent strain C3013, we used BL21DE3 instead), there was no activity in the Tnp activity assay at all. The protein size is correct on the SDS PAGE Gel. So I guess there must be some issues in the transpososome assembly. Would you please give me some advice?

Best!

[Simone78]

Have you tried to do the assembly in solution as we describe in the paper? Just elute the tn5 from the column and add the oligos in equimolar conc with the Tn5 --> incubate 37 degrees --> ready to use. If that doesn´t work then you might have an issue with the Tn5.
Best,
Simone

[kobeho24]

Have you tried to do the assembly in solution as we describe in the paper? Just elute the tn5 from the column and add the oligos in equimolar conc with the Tn5 --> incubate 37 degrees --> ready to use. If that doesn´t work then you might have an issue with the Tn5.
Best,
Simone

Actually, I did assemble the transpososome in solution @ 30C/RT for 1hr. Cuz I used to assemble a commercial unaasembled tn5 Tnp in this way. BTW, I was not only following the published paper but also the in-house protocol generously provided from your lab. So far, I might have to wait the arrival of the suggested strain, try one more time and see if it works. And, I was wondering that the incubation temperature after IPTG induction described on the Addgene webpage is 30C while your protocol shows that it should be 23C. As the temperature is crucial for polypeptide folding a correct way. I wanna make sure just in case. Thanks a lot!!!

Best!