Seqanswers Leaderboard Ad

Collapse

Announcement

Collapse
No announcement yet.
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Multiplex PCR missing some loci/low template

    I am trying to multiplex 12 primer sets in a single PCR. The goal is to amplify 12 taxon-specific loci from environmental samples. So, 1) DNA concentrations are low (<100 DNA copies/rxn) and 2) not all rxns contain all 12 loci (some might contain DNA from only one taxon).

    In my no template controls there is a pretty big primer dimer band. I tested all 66 possible primer pairs (n=2 primer pairs per rxn) and found that there is a small-medium size primer dimer band in ~1/2 of them. None of these heterodimers look bad from an in silico test. So I think the big primer dimer band in the full n = 12 multiplex is cumulative. I'm using a lot of cycles (n=40) because template concentration is low.

    The problem is that I'm *only* getting a primer dimer band in reactions where template is low (<100 copies/rxn) and there is only DNA from one taxon. I get fewer primer dimers and a better band as I increase template concentration and add in more taxa. I know that in singleplex I get one clean band of the expected size with the same PCR conditions.

    My hypothesis: The primer-primer interactions are relatively weak, but without other templates and with lots of cycles, heterodimer formation is taking over the mutliplex PCR.

    Does anyone have experience with a similar study design? Having trouble finding the lower limit on template quantities and the effect of missing loci on multiplex PCR. Any ideas on optimization (I know that I could up annealing temp, use TD-PCR, and decrease primer concentrations to start perhaps)?

  • #2
    I have tried a similar setup. 10 amplicons per multiplex. Only a few amplicons amplified, so I decreased the primer concentration for those amplicons, or increased the concentration for those that not amplified. For some, a missing amplicon appeared, but then an other disappeared. I think I did more than 20 optimization steps in changing concentrations and always some disappear or appear, but I could never get all of them. Also tried different annealing temperatures, MgCl concentrations, number of cycles, all without success.

    To conclude, I gave up...
    Multiplex sounds fine, but practical is complex to get it running. Maybe with primers with high annealing temperature (above 60-65°) it could work (some kits for amplifying cancer genes work that way), but that was impossible in my experiment.

    Comment

    Latest Articles

    Collapse

    • seqadmin
      Strategies for Sequencing Challenging Samples
      by seqadmin


      Despite advancements in sequencing platforms and related sample preparation technologies, certain sample types continue to present significant challenges that can compromise sequencing results. Pedro Echave, Senior Manager of the Global Business Segment at Revvity, explained that the success of a sequencing experiment ultimately depends on the amount and integrity of the nucleic acid template (RNA or DNA) obtained from a sample. “The better the quality of the nucleic acid isolated...
      03-22-2024, 06:39 AM
    • seqadmin
      Techniques and Challenges in Conservation Genomics
      by seqadmin



      The field of conservation genomics centers on applying genomics technologies in support of conservation efforts and the preservation of biodiversity. This article features interviews with two researchers who showcase their innovative work and highlight the current state and future of conservation genomics.

      Avian Conservation
      Matthew DeSaix, a recent doctoral graduate from Kristen Ruegg’s lab at The University of Colorado, shared that most of his research...
      03-08-2024, 10:41 AM

    ad_right_rmr

    Collapse

    News

    Collapse

    Topics Statistics Last Post
    Started by seqadmin, 03-27-2024, 06:37 PM
    0 responses
    13 views
    0 likes
    Last Post seqadmin  
    Started by seqadmin, 03-27-2024, 06:07 PM
    0 responses
    11 views
    0 likes
    Last Post seqadmin  
    Started by seqadmin, 03-22-2024, 10:03 AM
    0 responses
    53 views
    0 likes
    Last Post seqadmin  
    Started by seqadmin, 03-21-2024, 07:32 AM
    0 responses
    69 views
    0 likes
    Last Post seqadmin  
    Working...
    X