SEQanswers

Go Back   SEQanswers > Applications Forums > Sample Prep / Library Generation



Similar Threads
Thread Thread Starter Forum Replies Last Post
KAPA, dual-SPRI size selection yxl Sample Prep / Library Generation 6 01-17-2018 11:44 PM
Why aren't my SPRI beads doing a size-selection? jwfoley Sample Prep / Library Generation 14 11-11-2016 07:58 AM
Double sided SPRI for size selection -- Ion Library jhalpin Ion Torrent 0 04-10-2015 01:55 PM
Ampure XP beads Dual Bead-based Size Selection ratio and PCR purification Leo Lee Sample Prep / Library Generation 4 09-19-2014 09:36 AM
Double-SPRI size selection mgravina Sample Prep / Library Generation 3 11-08-2013 12:50 PM

Reply
 
Thread Tools
Old 06-17-2016, 06:30 AM   #1
sk8bro
Member
 
Location: boston

Join Date: Feb 2012
Posts: 30
Default SPRI Bead Size Selection: Ethanol concentration effect

I am curious about why the Ampure XP protocol calls for 70% Ethanol, while their SPRI Select (supposedly the same as Ampure XP with extra QC) calls for 85% Ethanol.

Has anyone used 70% with the SPRI Select product from Beckman?

Has anyone done an Ethanol concentration titration experiment to see if there is any effect on size selection?

I've read that lower than 70% Ethanol impacts yield, while higher than 70% Ethanol concentration results in inefficient washing away of smaller molecules. What is the mechanism? Anypne have any data?

Reference from Nature Protocols: http://www.gmo-qpcr-analysis.com/tan...ocols-2010.pdf

Thanks for your advice!
sk8bro is offline   Reply With Quote
Old 06-18-2016, 10:53 PM   #2
brofu
Junior Member
 
Location: California

Join Date: Mar 2015
Posts: 2
Default

Lowering the ethanol % in the wash steps will lower the overall yield without affecting the size distribution (as opposed to SPRI beads, where decreasing the amount of beads increases the insert size). If your yields are high enough you might be willing to sacrifice some good stuff to get rid of noise. If you've already tried decreasing the SPRI ratio as far as it could go and you still need more stringency then lowering the ethanol % could help.
brofu is offline   Reply With Quote
Old 06-28-2016, 09:37 AM   #3
ScienceGrrl
Junior Member
 
Location: Indianapolis, IN

Join Date: Jul 2015
Posts: 8
Default

For all SPRI products (AMPureXP, SPRIselect, etc) if you go lower than 68% EtOH, you will cause the nucleic acid to elute off the beads. For manual prep, there is usually not an issue so earlier protocols state to use 70%. As Beckman did more and more automation with the SPRI beads, they upped the concentration of the EtOH so it could sit on deck of the robot without dropping below the 68% threshold and allow for the errors that would sometimes happen if a user prepared the EtOH dilution incorrectly or used older prepared batch of EtOH. Going above 85% is not suggested because you decrease your yield as you are more likely to overdry the beads and cause the nucleic acids to be unable to elue properly.
ScienceGrrl is offline   Reply With Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off




All times are GMT -8. The time now is 04:24 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
Single Sign On provided by vBSSO