SEQanswers

Go Back   SEQanswers > Bioinformatics > Bioinformatics



Similar Threads
Thread Thread Starter Forum Replies Last Post
Assembling raw reads with Canu, but without correction ekarais Bioinformatics 2 05-21-2019 02:13 PM
R: Extract genes highly expressed in a k-means cluster ScientistShan Bioinformatics 0 07-20-2016 12:10 PM
How to phase haplotypes in a highly polymorphic genome from NGS data AdrianP Bioinformatics 1 01-14-2016 09:16 PM
Low Cluster PF % and highly skewed Base % sequencer13 Illumina/Solexa 17 06-23-2013 04:28 AM

Reply
 
Thread Tools
Old 11-25-2019, 06:47 AM   #1
drosophilid
Junior Member
 
Location: Colorado

Join Date: Nov 2019
Posts: 1
Default Assembling haplotypes of a highly heterozygous gene cluster with canu

I am trying to assemble haplotypes for a peculiar region of the human genome that (1) has high heterozygosity, (2) has variation in presence or absence of entire genes, and (3) encompasses a gene cluster of highly similar paralogues. This is obviously making assembly difficult, since a paralogue on the same chromosome may have only 10% divergence from its duplicate, while the homologue on the other chromosome has 5% differences due to segregating polymorphism at that locus. Currently, I have nanopore and short reads from this region, both at approximately 30X coverage. I would like to use canu to assemble the nanopore reads, then short reads to polish, but I am getting nowhere near the full assembly. My command is

Code:
canu -p prefix -d canu_run genomeSize=250k correctedErrorRate=0.144 minOverlapLength=500 -nanopore-raw sample.fastq
Here sample.fastq are reads filtered for my region of interest, so its a fairly small total assembly. So far, I have tried varying the corrected error rate between 0.1 and 0.2, and the minOverlapLength between 500 and 1000 with no luck. Using BLAST, I can see large chunks of my genes of interest in the prefix.unassembled.fasta file. It seems varying error rates should help find a sweet spot of expected divergence between reads from the same allele at a locus, reads from different alleles at a locus, and reads from different paralogous loci - I'm wondering, is there any other parameters I can vary to try and get a more complete assembly? Is there any preprocessing I can do with the more accurate short reads to lead to a more complete assembly? Ideally, I eventually want phased haplotype information.
drosophilid is offline   Reply With Quote
Old 11-25-2019, 10:15 AM   #2
SNPsaurus
Registered Vendor
 
Location: Eugene, OR

Join Date: May 2013
Posts: 512
Default

This isn't so helpful to solve the asked problem, but PacBio HiFi reads might be a better choice since you can generate 15kb sequences at 1% or 0.1% error rates. They might more obviously segregate into 4 bins (2 haplotypes at a locus, 2 at paralogous locus).
__________________
Providing nextRAD genotyping and PacBio sequencing services. http://snpsaurus.com
SNPsaurus is offline   Reply With Quote
Reply

Tags
assembly, canu, heterozygous, nanopore, phase

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off




All times are GMT -8. The time now is 06:31 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Single Sign On provided by vBSSO